Firing Circuit Drivers Airbag E36
The airbag light is on in my 98 Z3. (supply voltage) and #5 (firing circuit, belt tensioner, passenger side). (E36, E37) Airbag Light -- Seatbelt Pretensioner.
Recently my airbag light randomly arrived on. After searching around on the web site I noticed the only method to precisely diagnose the problem will be with a airbag program code readers/reset device. Ken at hooked me up and in a several times I experienced a sparkly new device. Here will be how I fixed the common seat belt pretensioner issue. My searching transformed up an interesting issue. Usually times the pretensioner itseIf isn't bad, simply the wiring.
BMW Airbag system: MRS 1 Model code: E36, E39 01 Internal CM Fault 02 Failure airbag warning lamp 03 Supply voltage low 04 Firing circuit driver's airbag. As per the title I've had the passenger airbag light on assessed and the error code is: 06 firing circuit, belt tensioner, passenger side I get the.
I has been hoping this was the case because the wires is significantly cheaper than thé pretensioner. I experienced a extra wiring control valuable. If you put on't (why wouId you) I wouId suggest ordering one (approximately $15) and attempting this before you invest in a brand-new pre-tensioner. Use this at your own risk.
1) This will be what I started with 2) Right here will be my brand fresh Peake tool from BimmerTools.com 3) Put in the Peake as well to the OBD slot that will be in the drivers part foot well. This should end up being attached to the underside stop plastic.but mine isn'tyeah. 4) Go through your requirements sticking with the directions that emerged with the tool, very easy. 5) My code has been table 10, code 02 which is drivers aspect pre-tensioner. 6) Begin by disconnecting the battery. 7) Detach the under seat connector freeing the chair from the wires funnel.
You can appear the connection open by using a screwdriver to move the slider/lock over towards thé centerline of thé vehicle. You can observe the lock is moved over a ring finger size in the 1st image. In the second picture you can discover the locking mechanism most of the method out (next to my browse). Unbolt the rear two seat bolts.
How To Install Drivers Airbag 2007 Ford Edge
9) Get rid of the plastic material caps covering the front seat nut products. 10) Get rid of the front side seat mounting bolts. 11) Eliminate the seat headrest, tilt the steering wheel upward and drive it all the way in.
Lift the chair up and move it about and snéak it out thé door. If you possess a four door you can leave the chair belt connected to the seat. I established the chair just outside the door. 12) Remove the wiring funnel from the pre-tensioner. 13) Remove the wiring harness put from under the seat by pressing the two videos on either aspect to release it, the glide it back.
Look at the 2nd image to know what you're attempting to unclip. 14) Cut the one squat link that retains the cables and undo the other wire keeping cut. 15) Eliminate the dark shield component of the link.
You require to pull back the videos on both edges. The cut is simply at the suggestion of my browse. 16) Get your new wiring control and connect it to thé pre-tensioner.
Wear't worry about redirecting the wires under the seat however. We would like to check the new wiring use before we bolt everything back again together. 17) Plug the yellow connectors together reconnecting the pré-tensioner to thé car. I rigged it up so I could connect in the seat while it had been seated outside next to the doorway. 18) Reconnect the battery pack, reconnect the Peake device, obvious the codes and mix your fingers! 20) If you're also airbag lighting is nevertheless on disconnect the battery pack and recheck all your cable connections, consider reseating all the fittings, plugs, etc and test once again.
If your airbag light is nevertheless on then you're heading to require to order the pre-ténsioner. Bolt everything back together for now until you get the brand-new components.
When it comes to investing -- and compounding -- you want to think in terms of decades, not years. 1000 ways to make 1000 dollars pdf. And sure, that 10% figure might seem, um, generous given, but remember that it's an average over many, many years, including those of the Great Depression. If you add money every year, the figure will become much, much greater.
21) Assuming the lights off it's i9000 now time to put everything back jointly. 22) Disconnect the battery and after that disconnect the chair wiring. 23) Course the wires on the seat back in the correctly (reverse of how you had taken everything apart), install the yellowish plug back again under the chair and you're ready to install the chair once again.
2011 Lincoln Mks Remove Drivers Airbag
24) Put the seat back in, boIt it down, réconnect the wiring, reconnect the battery, etc. 25) Done and done, best wishes! Writeup by: tim330i.
There is definitely a method to fool the program into considering that a passenger is seated in the chair. There is usually an 'occupancy sensor' embedded in the traveler seat and if this goes bad, after that the airbag lighting will continually be lit. The method to trick the system is usually to successfully sidestep this sensor. I do this and it worked well fine for me - at least I know that the airbags will set up in the occasion of an accident. More info is accessible on this internet site who market the bypass models. When I purchased mine, they had been promoting for only 14.99 +pp. Fitting has been a peice of cake.
Rookie Content: 2 Joined up with: Fri March 29, 2010 3:31 pm.
Comments are closed.